solar connections header image

Solar panels, modules or array mounts: Wattsun Solar Tracker, DEGERtraker 5000NT system, DPW, Unirac SnapNrack solar pv carport, multipole, tracker mounting systems for your residential, company or commercial solar project.

SOLAR PRODUCTS

Solar PV Panel Mounts and Mounting 10 items
1
Wattsun Active Solar Tracker
 Wattsun Active Solar Tracker Quality and Performance
 Azimuth trackers automatically track the sun’s path by rotating the PV array around the pipe, providing greater stability for larger arrays. The corners do not protrude down towards the ground or stick up in the air to catch the wind. The bottom edge of the array always remains parallel to the ground and requires less ground clearance than tilt and roll trackers. Wattsun’s azimuth trackers provide nearly 270 degrees of rotational movement and can adjust from 5 to 75 degrees of elevation tilt.

Wattsun Active Trackers feature an optical, sun-sensing device coupled with solid state electronic design and positive drive mechanisms. This tracker performs well in extreme temperatures and windy conditions. The standard single horizontal tracking model maintains horizontal tracking only. The dual azimuth tracker, has vertical tilt positioning, follows the suns elevation and collects more solar energy.

Wattsun Active Solar Tracker Rear View AZ-125 Azimuth Gear Drive Tracker
Mounts up to 1800 Watts (Up to 125 Sq. Ft. of PV array)
AZ-225 Azimuth Gear Drive Dual Tracker
Mounts up to 3300 Watts (Up to 225 Sq. Ft. of PV array)

 Environmental Practice
 Constructed from corrosion-resistant structural aluminum.

 Installation
 Wattsun Trackers are easy to install, easy to operate and
inexpensive to maintain.

Website: Wattsun
2
DEGER Traker 5000 NT and Candian Solar modules PACKAGE
 Deger 5000 NT system includes canadian solar modules Quality and Performance
Dual Axis Tracking Solar PV System 10kW
DEGER 5000 NT systems interactively track the sun. Continually repositioning the solar array toward the strongest irradiation, for maximum solar energy collection every day and are capable of generating 35 - 45% more exportable electricity than a fixed axis solar array, resulting in higher annual incomes from a Feed-In-Tariff program.

The DEGER Tracker 5000 NT is equipped with sensor cells that supply reference values to the system’s mechanical controls. Data collected by these sensor cells determine the daily tracking movement of the array. The tracking movements themselves are powered directly from the system’s own energy reserves, typically using less than 1 watt of power per day.

 DEGER Tracker 5000NT system includes solar panels
manufactured by Canadian Solar Inc (founded in Ontario 2001)
 The panels are perfectly suited to Ontario’s climate. Panel frames are constructed with a heavy duty, anodized aluminum alloy and the solar cells are covered with a low iron tempered glass, resulting in a strong module with a snow load capacity of 5400 Pa. Microinverter, monitoring system and online analysis tool complete the system.

 Environmental Practice
 Online analysis reports can be generated for a variety of time intervals and the Environmental Benefits of the system are calculated in terms of Carbon Offsets.

Installation
 As this is a complete system, everything is built to work together.

 Website: DEGER
DEGER Page - Google translation
3
MS DPW Pole Mounting
 MS DPW pole mounted solar pv panels Quality and Performance
 MS- DPW Pole Mount allows dual use of space.
Designed to mount on 3", 4" or 6" Schedule 40 galvanized steel pipe (installer supplied). Supports 2 to 4 modules high in landscape orientation. Limitless horizontal expansion.

Capable of significant ground clearance.
Full range of seasonal elevation adjustability.

Ideal for shade and carport structures. Multi pole design makes this a very versatile solar pv panel mounting solution.

Environmental Practice
 Fewer ground penetrations than traditional ground mounts.

 Installation
 Utilizes under-flange module clamp for installation ease.

Website: DWP Solar
MS DPW Multi Pole Mounts
4
Unirac SolarMount
 Unirac SolarMount Quality and Performance
 Any framed module sold in North America can be mounted using SolarMount. Once you’ve selected the PV modules and planned your installation layout, you’re ready to choose SolarMount components.

Select a Top-Mounting or Bottom-Mounting System. With Standard Rail, there are accessories to handle special circumstances, such as Spanish tile or an uneven roof.

Installation
 Unirac’s SolarMount is a fast, easy, safe way to install a PV array in virtually any roof or ground installation. Bottom mounting clips and tilt legs supplement traditional top mounting clamps.

As a result, the system accommodates the widest variety of installations and assembly preferences
on the roof and on the ground.

Website: UniRac
5
Unirac SunFrame
 Unirac SunFrame Components
  • Inter-module rails provide support shelves for the modules. Depending on module thickness, its upper surface can be as little as 2.125 inches above the roof. Rails come in bulk packs of eight 192 ″ pieces in clear-anodized or dark-bronze finish.
  • 192 ″ module-specific cap strips secure modules and finish the array topside, forming a gap-free frame. Self-drilling screws at 16 ″ intervals provide holding power. Order cap strips for the module brand and model to be installed. Cap strips are available in clear or dark bronze anodized finishes.
  • End caps finish rail ends to complete the frame.
  • L-feet attach directly through asphalt shingle roofs and support the rails one-half to three-quarters of an inch above the roof surface to provide convective air flow for ventilation.
  • Splices safely extend rails.
  • Standoffs (optional), designed for standard flashing, support L-feet above tile or shake roofs.
Quality and Performance
 When an installation has to look great, SunFrame offers finish choices and low, clean lines that become as natural a part of a home as a skylight. The rails are available in clear and dark bronze finish to match the module frames. The SunFrame rails run horizontally across the roof between the modules making the array look like one large skylight. Installation is slightly more difficult than using SolarMount with top clamps because rail alignment must be perfect. Since the modules will sit closer to the roof, the array may operate at a higher temperature and there may be a small loss of performance. Note: SunFrame cannot be used with REC AE-US modules.

Website: UniRac
6
Unirac U-LA
 Unirac U-LA Ground or Roof Mounting array Quality and Performance
 A commercial grade mounting system using large arrays of PV modules designed to generate 3 kilowatts or more. The size of the system is limited only by the available space for the array.

The U-LA can be installed on the ground or on commercial flat roofs.

 Installation
 Made to suit your site. Please contact us with your requirements. Unirac U-LA Ground or Roof Mounting

Website: UniRac
7
DPW Solar POWER -FAB CRS PV Ballasted Flat Roof Mounting System
 DPW Solar Power-Fab CRS PV Ballasted Flat Roof Mount Quality and Performance
 Ballasted PV mounting systems are used when the roof is a flat or very slightly pitched surface and the installation requires minimal or no penetrations. They are usually used in commercial systems. The advantages are short installation time, minimal penetrations of the roof means less chance of leakage, but there can be high weight loading on the roof, and the modules will a have very low tilt angle.

The CRS system typically adds less weight per square foot than competitive products.

The POWER-FAB CRS system offers a variety of tilt angles from 5 to 25 degrees and features the flexibility to design the racking around roof obstructions and shaded areas to maximize the number of modules and total energy production.

 Installation
 The POWER-FAB CRS top-clamping module mounting system is designed to install fast and provide a secure mounting structure for any framed module. The system's ballasted design minimizes the impact of dead loads on the roof and eliminates roof penetrations.

Website: DWP Solar
8
SnapNrack Roof Mounting System
 SnapNrack solar pv panel mounting system Quality and Performance
SnapNrack is a top-down roof mounting solution, load tested and engineered for up to 150 mph wind speeds and 100 psf snow loads. See www.snapnrack.com for full details. SnapNrack is compatible with modules from virtually any manufacturer and ensures a low profile installation on your roof.

SnapNrack standoffs are height-adjustable to ensure a clean, level installation on even the most uneven roof surface. Tilt-up can be achieved with pieces of cut rail and L-feet. Rails and components have a 10-year warranty.




 Installation
 SnapNrack was developed quick, efficient installation. It simplifies and reduces the cost of the solar installation process. Snap-in sliding channel nuts ensure quick and easy installation and precise alignment. Mid-clamps are a half-inch wide to keep the math simple. Every bolt in the system uses the same size wrench.

Can be used with Quick Mount PV All-In-One Waterproof Flashing

Website: SnapNrack
9
Quick Mount PV All-In-One Waterproof Flashing
 Quick Mount PV Roof Flashing Quality and Performance
The Quick Mount PV product is an all-in-one waterproof flashing and mount designed to anchor photovoltaic racking systems to a new or existing roof. The flashing includes an attached standoff block and stainless steel hardware to attach with an L-foot to racking from Unirac, DP&W, and SnapNrack. No roof cutting is required.

Sold in boxes of 12 flashings. Use of a roofing bar to remove nails is recommended.


 Installation
 Shake Mount Flashing - This 18"x 18" aluminum flashing is large enough to do a good job flashing on wood shake roofs. Available in mill finish, clear anodized or bronze anodized finish.

Flat Tile Mount - The flat tile mount is comprised of an all-aluminum mount and tile flashing cover. All stainless steel hardware is included. The aluminum tile cover replaces one existing tile. It works with most tiles that measure from 11-1/2" to 12-3/8" wide and have a pan lip on the left side and a cover lip on the right side.

Curved Tile Flashing - The curved tile mount is comprised of all-aluminum standoff and flashing. All hardware is included. The tile is removed, the standoff is bolted into position, the tile is cut to allow for the standoff to pass through. An additional peel-and-stick flashing is included for waterproofing at the sub-roof. The aluminum flashing is then placed and molded to the shape of the tiles.

Composition Shingle Flashing - The composition shingle flashing mount is made of aluminum and steel hardware. It works with all standard racks, installs seamlessly and provides lowprofile mount. The flashing includes an attached standoff block and stainless steel hardware.

Website: Quick Mount PV Waterproof Roof Flashing
10
Technical Date and Specifications
  
Please get in touch with us if you need further details on these products.



Tel: 705 241 8840 or

buttonAsk about Mounting Solutions